If you’re like most people, you depend on your car to get you where you need to go. But what happens when your key fob battery dies and you can’t get into your car? Don’t worry, changing the battery in your Subaru key fob is a quick and easy process. In this article, we’ll show you how to change the battery in your Subaru key fob in just a few simple steps.
So, how to change battery in subaru key fob?
The most common way to change the battery in a Subaru key fob is to use a small flathead screwdriver. First, remove the screws that hold the back cover in place. Next, use the screwdriver to pry open the back cover. Once the back cover is open, you will see the battery. Remove the old battery and insert the new one. Finally, screw the back cover back on and test the key fob to make sure it is working properly.
Let’s dig into it and see what’s inside.
How To Change Battery on Subaru Key Fob?
Step-1: Remove the emergency key from the bottom of the smart key by pressing the button on the back.
Step-2: Use a flathead screwdriver to twist the silver piece in the notch on the side of the smart key.
Step-3: Pull the back of the smart key off to reveal the circuit board and battery unit.
Step-4: Use the flathead screwdriver to remove the old battery from the circuit board.
Step-5: Install the new battery on the circuit board with the plus side up.
Step-6: Put the circuit board back in the front of the shell and snap the back of the shell on.
Step-7: Put the emergency key back in the smart key.
How Do I Change The Battery In My Subaru Key?
If your Subaru key fob battery is dead, you’ll need to replace it. Here’s how:
1. Start by finding the release button on your key fob. This is usually located on the back of the fob.
2. Once you’ve found the release button, press it to pop open the back of the fob.
3. Inside the fob, you’ll see the battery. It will be clearly marked with the + and – symbols.
4. Use a small flathead screwdriver to gently pry out the old battery.
5. Insert the new battery, making sure the + and – symbols match up.
6. Close the back of the key fob and you’re all set!
What Battery Goes In A Subaru Key Fob?
Your key fob is an important part of your car, and the battery is one of the most important parts of the key fob. So, what battery goes in a Subaru key fob?
The most popular batteries for Subaru key fob battery replacement are CR2032 3V and CR2025 3V. These are the most common batteries that are used in key fobs, and they are both 3-volt batteries.
However, there are other types of batteries that can be used in a Subaru key fob. It is essential to check the manual of your car to know the perfect battery type for your fob. Depending on the model of your car, the manual will recommend a different type of battery.
The CR2032 3V battery is the most common type of battery used in key fobs. It is a small, coin-shaped battery that is 3-volt. This type of battery is often used in watches, calculators, and other small electronic devices.
The CR2025 3V battery is another common type of battery used in key fobs. It is also a small, coin-shaped battery that is 3-volt. However, the CR2025 battery is slightly larger than the CR2032 battery.
It is important to note that there are other types of batteries that can be used in a Subaru key fob. If you are unsure about which type of battery to use, it is always best to consult the manual of your car. The manual will have the most up-to-date information on the best type of battery to use in your car.
As well as that, Subaru key fobs use batteries CR2032 3V and CR2025 3V. These are popular batteries for key fob replacement, but it is essential to check the manual of your car to know the perfect battery type for your fob.
How Do I Start My Subaru With A Dead Key Fob?
If your key fob is dead, there are a few things you can do to start your Subaru. First, check the battery. If it’s dead, you’ll need to replace it. If the battery is fine, try pressing the button on the key fob. If that doesn’t work, you can try holding the key fob up to the start button on your Subaru. If that doesn’t work, you can always use the key to start your Subaru.
How Do You Change The Battery In A Subaru 2018 Key Fob?
If you’re like most people, you probably don’t think about your car key fob very often. But when it stops working, it can be a huge pain. The good news is that changing the battery in a Subaru 2018 key fob is a relatively easy process. Here’s a step-by-step guide on how to do it:
1. Start by finding the small release button on the back of the key fob. This is usually located near the bottom.
2. Press the release button and then pull the back cover off of the key fob.
3. Take out the old battery and then insert the new one. Be sure to match the positive and negative sides.
4. Put the back cover back on and then press the release button to lock it in place.
5. Test the key fob to make sure it’s working properly.
If you have any trouble changing the battery in your Subaru 2018 key fob, be sure to contact a professional. They’ll be able to help you out and make sure that your key fob is working properly.
What Is The Battery Life Of A Subaru Key Fob?
This is a question that is often asked by Subaru owners, as they want to know how long their key fob’s battery will last. The answer to this question is that the battery life of a Subaru key fob will vary depending on the model and year of the key fob. However, most Subaru key fobs will have a battery life of around two years.
How Long Does The Average Subaru Key Fob Battery Last?
is a question we get all the time here at YourMechanic. We decided to ask our expert mechanics to help answer this question for all our Subaru-driving readers out there.
The average key fob battery lasts between 2 and 5 years, depending on the brand of battery and how often you use your key fob. If you use your key fob regularly (i.e. to unlock your car doors or start your car engine), then you can expect the battery to last on the lower end of the spectrum. Conversely, if you only use your key fob occasionally, then you can expect the battery to last on the higher end of the spectrum.
There are a few things you can do to extend the life of your key fob battery, such as:
– Avoid exposing the key fob to extreme temperatures (i.e. hot or cold).
– Remove the key fob from your key ring when you’re not using it.
– Store the key fob in a cool, dry place.
– Avoid dropping or banging the key fob.
If you notice that your key fob isn’t working as well as it used to (i.e. the range is shorter or the buttons are less responsive), then it’s probably time to replace the battery. Luckily, this is a relatively simple and inexpensive process that you can do yourself at home.
If you have any questions about how to change your key fob battery or if you need help troubleshooting any other key fob issues, then feel free to reach out to one of our expert mechanics. We’re always happy to help!
What Is The Average Lifespan Of A Subaru Key Fob Battery?
This is a question that we get fairly often here at the dealership. The answer, unfortunately, is not as cut and dry as we would like it to be. Subaru key fob batteries can last anywhere from a couple of years to upwards of five years, depending on a variety of factors.
So, what determines how long a Subaru key fob battery will last? First, it depends on the type of battery that is used in the key fob. There are two common types of batteries used in key fobs: CR2032 and CR2025. The CR2032 batteries are slightly larger in size and tend to have a longer lifespan than the CR2025 batteries.
Another factor that can affect the lifespan of a Subaru key fob battery is how often the key fob is used. If you are someone who uses their key fob multiple times throughout the day, the battery is going to drain quicker than someone who only uses it occasionally. Additionally, if you live in a warmer climate, the heat can also shorten the lifespan of the battery.
If you are looking to extend the lifespan of your Subaru key fob battery, there are a few things that you can do. First, try to avoid exposing the key fob to extreme temperatures, both hot and cold. Also, if you are not using the key fob for an extended period of time, it is a good idea to remove the battery. This will prevent the battery from slowly draining over time.
If you find that your Subaru key fob battery is starting to die prematurely, there are a few things that you can do to try and revive it. First, try removing the battery and then re-inserting it. Sometimes, this can reset the key fob and help the battery to last longer. If that doesn’t work, you can try replacing the battery with a new one.
If you are still having issues with your Subaru key fob
What Type Of Battery Does The 2017 Subaru Impreza Use In Its Key Fob?
If you’re the owner of a 2017 Subaru Impreza, you might be wondering what type of battery it uses in its key fob. Here’s a quick guide to help you out.
The 2017 Subaru Impreza uses a CR2032 battery in its key fob. This is a 3-volt coin-type battery that’s widely available at most electronics stores.
To replace the battery in your key fob, start by removing the keychain. Then, use a small flathead screwdriver to pry open the back of the key fob. You should see the battery inside.
Gently remove the old battery and then insert the new one, making sure that the positive side is facing up. Once the new battery is in place, close up the key fob and reattach the keychain.
If your key fob starts to act erratic or doesn’t work at all, chances are it’s time for a new battery. By following these simple steps, you can easily replace the battery in your 2017 Subaru Impreza’s key fob.
Will My Subaru Key Fob Work If The Battery Is Low?
If you’re like most people, you probably don’t think much about your car key fob until it stops working. If your Subaru key fob does stop working, it’s probably because the battery is low.
Although it’s not impossible for the key fob to stop working for other reasons, a low battery is the most likely culprit. If your key fob is more than a few years old, the battery may simply be worn out and need to be replaced.
If you have a newer key fob, the battery may just need to be recharged. You can do this by placing the key fob in a bowl of rice overnight. The rice will absorb the moisture from the battery and help to recharge it.
If your key fob still isn’t working after you’ve tried these things, it’s time to contact a Subaru dealer or locksmith to see if they can help.
How To Change The Battery In The “Teardrop” Subaru Key Fob?
If you own a Subaru, you may have noticed that your key fob looks a bit different than most. That’s because it’s what’s known as a “teardrop” key fob. And while it may look different, it actually is pretty easy to change the battery in it. Here’s a quick guide on how to do it:
First, start by finding a small Phillips head screwdriver. Then, locate the small screw on the back of the key fob. Once you’ve found it, unscrew it and then separate the two halves of the key fob.
Next, you’ll see a small circuit board inside the key fob. On this circuit board, you’ll see a small battery. Gently pry this battery out and then insert the new one. Make sure that the positive side of the new battery is facing up.
Once the new battery is in place, simply screw the back of the key fob back on and you’re all done! It’s really that easy. So if your Subaru key fob starts to act a bit funky, don’t panic. Just change the battery and you should be good to go.
How To Change The Battery In The “Fixed Key” Subaru Key Fob?
If you own a Subaru, chances are you have a “fixed key” fob. This means that the battery in your key fob is not replaceable. So what do you do when the battery dies?
The first step is to locate the release button. This is usually located on the back of the key fob, near the bottom. Once you have located the release button, press it and the back of the key fob should pop open.
Next, you will need to remove the old battery. Depending on the model of your key fob, there may be a small tab that you need to depress in order to release the battery. Once the old battery is out, simply insert the new one in its place. Be sure to orient the new battery so that the positive and negative terminals are in the correct positions.
Once the new battery is in place, close the back of the key fob and you’re done! Your key fob should now be working properly.
How To Change The Battery In The “Simple” Subaru Key Fob?
If you own a Subaru, you know that the key fob is anything but simple. In fact, it’s pretty darn complicated. But, that’s okay! We’re here to help.
Replacing the battery in your Subaru key fob is actually pretty easy, once you know how. Here’s a step-by-step guide:
1. Start by removing the key from the key fob. There should be a small release button that you can press to pop the key out.
2. Once the key is out, take a look at the back of the key fob. You should see a small screw. Use a small screwdriver to remove the screw.
3. With the screw removed, you should now be able to pry open the back of the key fob. Be careful not to lose the small spring that may pop out when you open the key fob.
4. Once the back of the key fob is open, you should see the battery. It will be clearly marked with a + and a -.
5. Use a small screwdriver to pry out the old battery. Be careful not to touch the circuitry with the screwdriver.
6. Insert the new battery, making sure that the + and – match up with the markings on the key fob.
7. Close up the key fob and screw it shut.
8. Test the key fob to make sure it’s working properly.
And that’s it! You’ve successfully changed the battery in your Subaru key fob.
How To Change The Battery In The “Rectangular” Subaru Key Fob?
If you have a Subaru with a “rectangular” key fob, here’s how to change the battery:
1. Start by removing the key from the key fob.
2. Next, use a small flat-head screwdriver to pry open the back cover of the key fob.
3. Once the back cover is off, you should see a small battery inside.
4. Use a small pair of pliers to remove the old battery and then insert the new one, making sure the “+” and “-” signs are facing the correct way.
5. Finally, replace the back cover and screw it back on.
Your Subaru key fob should now be working properly again!
How To Change The Battery In The “Silver Sides” Subaru Key Fob?
If your Subaru key fob starts to act up, it might be time to change the battery. Luckily, this is a relatively easy process that you can do at home. Here’s a step-by-step guide on how to change the battery in the “silver sides” Subaru key fob.
1. Start by removing the screw that is holding the back cover in place. You will need a small Phillips head screwdriver for this.
2. Once the back cover is off, you will see the battery. It is a CR2032 coin cell battery.
3. Use a small flathead screwdriver to pry the old battery out of its slot.
4. Put the new battery in the slot, positive side up.
5. Replace the back cover and screw it in place.
Your Subaru key fob should now be working properly. If it isn’t, you may need to take it to a dealer or locksmith to have it reprogrammed.
Final Word
Thanks for reading! Now that you know how to change the battery in your Subaru key fob, be sure to do so when the battery starts to die. It’s a simple process that takes less than five minutes, and it’s worth it to keep your key fob working properly.
If you have any questions about changing the battery in your Subaru key fob, feel free to leave a comment below. And be sure to check back soon for more helpful tips and tricks for your Subaru.
Related Post:
