How To Change Battery In Vt Commodore Key?

As an Amazon Associate, I Earn From Qualifying Purchases.

Last Updated on September 15, 2022 by Ellis Gibson (B.Sc. in Mechanical Engineering)

If you’re like most people, you probably use your key fob to unlock your car doors and trunk, and to start the engine. But did you know that your key fob has a battery that needs to be changed from time to time? If you’re having trouble with your key fob, it might be because the battery is low. In this article, we’ll show you how to change the battery in your vt commodore key.

So, how to change battery in vt commodore key?

To change the battery in a VT Commodore key, first remove the key from the ignition. Next, locate the battery cover on the back of the key. Use a small screwdriver to remove the cover, then gently pry out the old battery. Replace the old battery with a new one, making sure the positive (+) side is facing up. Replace the battery cover and reinsert the key into the ignition.

Let’s dig into it and see what we can uncover.

Step By Step Process On: How To Change Battery In Vt Commodore Key?

Here I will explain you step by step process of how to change battery in vt commodore key? let’s see how to change battery in vt commodore key.

REQUIRED TOOLS:

  1. Phillips head screwdriver
  2. Flathead screwdriver
  3. Super glue or duct tape
  4. New batteries

Step-01:

To change the battery in your vt commodore key, first unscrew the two screws on the back of the key using a Phillips head screwdriver.

Step-02:

Carefully pry open the two halves of the key with a flathead screwdriver, being careful not to break the plastic casing.

Step-03:

Remove the old battery from the key by carefully prizing it off with a flathead screwdriver.

Step-04:

Install the new battery in the key, making sure that the positive and negative terminals are correctly aligned.

Step-05:

Use a small amount of super glue or duct tape to seal the key halves back together.

Step-06:

Screw the two halves of the key back together using the Phillips head screwdriver.

Step-07:

Test the key to make sure that the new battery is working correctly.

If you wanted to watch a youtube video that shows you how to change battery in vt commodore key? I have included a video below:

How Do You Change The Battery In A Commodore Key?

If you’ve ever been curious about how to change the battery in a Commodore key, we’ve got you covered. It’s a pretty simple process, and we’ll walk you through it step-by-step.

First, start by locating the battery cover on the back of the key. Once you’ve found it, use a small flat-head screwdriver to pry it off.

Next, remove the old battery from the key. Once the old battery is out, take the new battery and insert it into the key, making sure that the positive and negative sides are facing the correct way.

Finally, replace the battery cover and screw it back into place. And that’s it! You’ve now successfully changed the battery in your Commodore key.

What Battery Goes In A Commodore Key?

When it comes to car keys, there are a few different types that use different batteries. For example, newer cars often have transponder keys that use a CR2032 battery, while older cars may have a more traditional key that uses a AA or AAA battery. So, what battery goes in a Commodore key?

The answer is that it depends on the type of key you have. If you have a transponder key, then you will need a CR2032 battery. If you have a more traditional key, then you will need a AA or AAA battery.

If you’re not sure what type of key you have, the best way to find out is to check the owner’s manual for your car. It should list the type of battery that is required for your particular key.

Furthermore, This is a listing for a set of Holden Commodore car key remote batteries. The batteries are CR2032 batteries. Shipping is free.

How Do You Program A Vt Commodore Key?

If you’re looking to program a VT Commodore key, there are a few things you’ll need to do. First, you’ll need to select the “Programming” option on your scan tool. Once you’ve done that, select the “Reprogram All Transponder Keys” option. From there, you’ll need to read the disclaimer and press the F1, F2, F3, and F4 keys on your scan tool to continue.

Once you’ve done that, turn the ignition on and press enter. Note that all programmed keys will need to be programmed again, or they’ll be deleted from the system. Press enter to continue and you should be all set!

Besides this, This process will allow you to select and program all of the transponder keys that are associated with your vehicle. In order to do this, you will need to read and accept the disclaimer that is presented to you. Once you have done that, you will need to press the F1, F2, F3, and F4 keys on your scan tool. After that, you will need to turn on the ignition and press the enter key. Please note that all keys that have been programmed previously will need to be programmed again. Otherwise, they will be deleted from the system. Press the enter key to continue.

How Do You Change The Battery In A Ve Commodore Key Fob?

If you own a VE Commodore, then you may be wondering how to change the battery in the key fob. The process is actually quite simple and only takes a few minutes.

First, you will need to locate the small screw on the back of the key fob. Once you have located the screw, you will need to use a small Phillips head screwdriver to remove it.

Once the screw has been removed, you will then need to gently pry open the back of the key fob. Be careful not to lose the small spring that is located inside the key fob.

Once the back of the key fob has been pried open, you will then need to remove the old battery. To do this, simply use your finger to push the old battery out of the key fob.

Once the old battery has been removed, you will then need to insert the new battery. Make sure that the positive side of the battery is facing up. Once the new battery is in place, you will then need to close the back of the key fob and screw it shut.

That’s it! You have now successfully changed the battery in your VE Commodore key fob.

Final Word

If you need to change the battery in your VT Commodore key, here’s how to do it:

1. Start by removing the key from the ignition.

2. Use a small screwdriver to pop off the cap on the back of the key.

3. Take out the old battery and insert a new one.

4. Put the cap back on and reinsert the key into the ignition.

5. You’re all set!

Related Post:

Share
Tweet
Pin
Share