How To Change Battery Jeep Key Fob?

As an Amazon Associate, I Earn From Qualifying Purchases.

Last Updated on September 15, 2022 by Ellis Gibson (B.Sc. in Mechanical Engineering)

It’s happened to all of us—you go to unlock your Jeep and the key fob just doesn’t work. If it’s been a while since you changed the battery in your Jeep key fob, it might be time for a replacement. In this article, we’ll show you how to replace the battery in a Jeep key fob in just a few simple steps.

So, how to change battery jeep key fob?

To replace the battery in your Jeep key fob, follow these steps:

1. Locate the screws on the back of the key fob. 2. Remove the screws with a Phillips head screwdriver. 3. Pry open the key fob case with a flathead screwdriver. 4. Remove the old battery and insert the new one, making sure the positive (+) side is facing up. 5. Close the key fob case and screw it shut. 6. Test the key fob to make sure the new battery is working.

Let’s dig into it and find out what’s going on.

Step By Step Process On: How To Change Battery Jeep Key Fob?

Here I will explain you step by step process of how to change battery jeep key fob? let’s see how to change battery jeep key fob.

REQUIRED TOOLS:

  1. New Battery
  2. Thin Screwdriver (optional)

Step-01:

First thing you want to do is get everything that you need. All you really need is a new battery. This takes the 2:03 – I got this off Amazon. There’s a link below in the description that six-pack was about five dollars. And optional item is a thin screwdriver. It’s not mandatory but it is helpful.

Step-02:

Because first thing you want to do is release the actual key. So pull that down. Push that out now right here insert the key right here and twist. There you go. A circuit board that stays right there. And then there is your battery.

Step-03:

So I find it best to hit that side right there that’s a 2-0 3-2 battery take that out get your new one put that in this this side first push it down then take the top part have a nice squeeze once you get lined up okay put your key back in and you’re all set.

Step-04:

Thanks for watching make sure you hit that thumbs up button.

If you wanted to watch a youtube video that shows you how to change battery jeep key fob? I have included a video below:

How Do You Change The Battery In A 2018 Jeep Key Fob?

If you own a 2018 Jeep Wrangler, then you know that the key fob is an essential part of the vehicle. The key fob allows you to unlock and lock the doors, as well as start the engine without having to use a key. However, like all batteries, the key fob battery will eventually die and need to be replaced. Here is a step-by-step guide on how to change the battery in a 2018 Jeep Wrangler key fob.

1. Start by locate the key fob. The key fob is usually located on the driver’s side of the vehicle, near the steering wheel.

2. Once you have located the key fob, you will need to remove the keychain from the key fob. To do this, simply press the release button on the key fob and then pull the keychain away from the key fob.

3. Next, you will need to remove the back cover of the key fob. There is usually a small tab or button that you will need to press in order to release the back cover. Once the back cover is off, you will be able to see the battery inside the key fob.

4. Using a small flathead screwdriver or a coin, gently pry the old battery out of the key fob.

5. Take the new battery and insert it into the key fob, making sure that the positive and negative sides are facing the correct way.

6. Once the new battery is in place, replace the back cover of the key fob and then reattach the keychain.

That’s it! You have now successfully changed the battery in your 2018 Jeep Wrangler key fob.

What Battery Does Jeep Key Fob Take?

A key fob is a small, hand-held remote used to unlock and lock a car door. They typically have buttons for locking, unlocking, opening the trunk, and sometimes panic. Newer models may also have buttons to control other functions like the headlights, windows, and sunroof.

The most common type of key fob uses a small CR2032 coin-cell battery. These batteries are readily available at most convenience stores, drug stores, and even some grocery stores. Replacing the battery is a simple matter of popping open the key fob, removing the old battery, and inserting the new one. Make sure the negative side of the new battery is facing down when you put it in.

Once the new battery is in place, reassemble the key fob and you’re good to go. If your key fob starts acting funky after replacing the battery, it may be time to get a new one.

As well as that, In order to change the battery in a key fob, you will need a CR2032 battery. First, insert the new battery into the keypad, making sure the negative side is down. Next, put the circuit board into the keypad, and then put the keypad into the key. Finally, snap the two key fob halves together.

How Do You Change The Battery In A 2017 Jeep Key Fob?

If you’re like most people, you probably don’t think about your car key fob until it stops working. Then you’re scrambling to figure out how to change the battery. If you have a 2017 Jeep, the process is actually pretty simple. Here’s a step-by-step guide to changing the battery in your 2017 Jeep key fob:

1. Start by removing the key fob from your key ring. You’ll need a small flathead screwdriver to pop open the back of the key fob.

2. Once the back is open, you’ll see the battery. It’s a CR2032 3-volt lithium coin cell battery.

3. Use your screwdriver to pry the old battery out of the key fob.

4. Insert the new battery, positive side up.

5. Close the back of the key fob and you’re all set!

If your key fob starts acting weird or doesn’t work at all, changing the battery is a good first step to try. It’s a quick and easy fix that could save you a lot of headache down the road.

How Do You Change The Battery In A 2018 Jeep Renegade Key Fob?

If you’re like most people, you probably don’t think about your car key fob very often. But when it starts to act up, it can be a real pain. One of the most common problems is a dead battery. If your key fob has a dead battery, it might not seem like a big deal. After all, you can just use the key to unlock your car door. But if you have a keyless entry system, a dead key fob can be a real pain. Luckily, changing the battery in a Jeep Renegade key fob is a pretty easy process.

First, you’ll need to find the right size battery. The 2018 Jeep Renegade uses a CR2032 battery. Once you have the right battery, just pop open the key fob and replace the old battery with the new one. That’s it! Just make sure to dispose of the old battery properly.

If your key fob is still giving you trouble after changing the battery, it might be time to replace it entirely. You can usually find replacement key fobs online or at your local auto parts store.

Final Word

It’s time to replace the battery in your Jeep key fob. Here’s how:

1. Start by removing the key fob from your Jeep.

2. Locate the battery cover on the back of the key fob.

3. Use a small screwdriver or other tool to pry off the battery cover.

4. Remove the old battery and insert a new CR2032 battery.

5. Replace the battery cover and reattach the key fob to your Jeep.

You’re now ready to hit the road with a new battery in your Jeep key fob!

Related Post:

Share
Tweet
Pin
Share