How To Change Battery Jeep Wrangler Key Fob?

As an Amazon Associate, I Earn From Qualifying Purchases.

Last Updated on September 15, 2022 by Ellis Gibson (B.Sc. in Mechanical Engineering)

If you’ve ever had your Jeep Wrangler key fob battery die on you, then you know how frustrating it can be. Luckily, changing the battery is a quick and easy fix. In this article, we’ll show you how to change the battery in your Jeep Wrangler key fob.

So, how to change battery jeep wrangler key fob?

If your Jeep Wrangler key fob battery is dead, you can change it in just a few minutes. You’ll need a small Phillips head screwdriver and a new battery. The first step is to locate the small screw on the back of the key fob. Once you’ve found it, use the screwdriver to remove the screw. Next, pry open the back of the key fob with your fingers. The battery is located inside and is held in place with a small tab. Use your fingers or a small flathead screwdriver to release the tab and then carefully remove the battery. To install the new battery, simply reverse the process. Place the new battery in the key fob and then use the screw to secure the back in place.

Let’s dig into it and see what secrets it holds.

Step By Step Process On: How To Change Battery Jeep Wrangler Key Fob?

Here I will explain you step by step process of how to change battery jeep wrangler key fob? let’s see how to change battery jeep wrangler key fob.

REQUIRED TOOLS:

  1. a new battery (2450 type)
  2. a small screwdriver
  3. the key fob needing a new battery

Step-01:

First, you will need a new battery. You can purchase these online or at most electronics stores. The type of battery you will need is a 2450.

Step-02:

Once you have your new battery, locate the key fob that you need to change the battery for. There is a small indentation at the base of the fob.

Step-03:

Use a small screwdriver to pop open the fob. There is a small notch that makes it easy to do this.

Step-04:

Once the fob is open, insert the new battery making sure that it is secure. You will know it is secure when you hear a small pop.

Step-05:

That’s it! You have now successfully changed the battery in your Jeep Wrangler key fob.

If you wanted to watch a youtube video that shows you how to change battery jeep wrangler key fob? I have included a video below:

How Do I Change The Battery In My Jeep Wrangler Key Fob?

If you’re like most Jeep Wrangler owners, you probably don’t think about your key fob very often – until it stops working. Then, it’s all you can think about!

If your Jeep Wrangler key fob has a dead battery, changing it is a pretty simple process. Here’s a step-by-step guide on how to do it:

1. Start by removing the key fob from your key ring. Most key fobs have a small release button or tab that you can press to detach the fob.

2. Once the key fob is detached, take a look at the back. You should see a small screw or panel that you can remove to access the battery.

3. Use a small screwdriver or knife to remove the screw or panel, and then take out the old battery.

4. Insert the new battery, making sure that the positive (+) side is facing up.

5. Replace the screw or panel, and then reattach the key fob to your key ring.

And that’s it! Once you’ve changed the battery, your Jeep Wrangler key fob should be good as new.

What Battery Does My Jeep Wrangler Key Fob Take?

Your Jeep Wrangler key fob needs a CR2032 battery. You can find this type of battery at most electronics stores. To replace the battery, first remove the old battery from the key fob. Next, insert the new CR2032 battery into the key fob, making sure that the negative side of the battery is facing down. Then, place the circuit board back into the key fob and snap the two halves of the key fob together. Start by snapping the key fob together near the key, and then work your way to the end.

Furthermore, Insert a new CR2032 battery with the negative side down. Place the circuit board into the key pad, then the key pad into the key. Snap the two halves together starting at near the key and working to the end.

How Do You Change The Battery In A Jeep Wrangler Key Fob 2018?

If you’re like most people, you probably don’t think about your car key fob until it stops working. Then you’re scrambling to figure out how to change the battery in a Jeep Wrangler key fob. Luckily, it’s not a difficult task and only takes a few minutes to complete.

First, you’ll need to locate the battery cover. On most key fobs, this is located on the back of the device. Once you’ve located the cover, use a small screwdriver or a paperclip to pry it open.

Once the cover is off, you’ll see the battery inside. Using your thumb or a small tool, gently press on the tab to release the battery.

Now, take your new battery and insert it into the key fob, making sure the positive (+) side is facing up. Once the battery is in place, replace the cover and screw it back on.

And that’s it! You’ve successfully changed the battery in your Jeep Wrangler key fob.

How Do You Change The Battery In A 2019 Jeep Key Fob?

If you’re like most people, you probably don’t think about your car key fob until it stops working. But when it does, it can be a major inconvenience. The good news is, changing the battery in a 2019 Jeep key fob is a relatively simple process that you can do at home.

First, locate the small release button on the back of the key fob. This is usually located near the bottom. Press the release button to pop open the back of the key fob.

Once the back is open, you should see a small battery. Gently remove the old battery and insert the new one, making sure that the positive and negative sides are facing the correct way.

Once the new battery is in place, close the back of the key fob and test it to make sure it’s working properly. If it doesn’t work, double-check the battery to make sure it’s properly installed.

That’s all there is to it! With a new battery, your key fob should be working like new again.

Final Word

If your Jeep Wrangler key fob battery is dead, you can easily change it yourself. All you need is a small screwdriver and a new CR2032 battery. Just follow these simple steps:

1. Remove the screw from the back of the key fob with a small screwdriver.

2. Pop open the back of the key fob to reveal the battery.

3. Remove the old battery and replace it with the new one.

4. Close the back of the key fob and screw it shut.

That’s all there is to it! Now your Jeep Wrangler key fob will be good as new.

Related Post:

Share
Tweet
Pin
Share