How To Change Battery Jetta Key Fob?

As an Amazon Associate, I Earn From Qualifying Purchases.

Last Updated on September 15, 2022 by Ellis Gibson (B.Sc. in Mechanical Engineering)

If you’re like most people, you probably don’t think about your car key fob until it stops working. Then you’re scrambling to figure out how to change the battery. Don’t worry, we’re here to help. In this article, we’ll show you how to change the battery in your Jetta key fob. We’ll also talk about some common problems that can cause your key fob to stop working and what you can do to prevent them.

So, how to change battery jetta key fob?

To change the battery in your Jetta key fob, you will need to first locate the small Phillips head screw on the back of the fob. Once you have located the screw, you will need to remove it with a Phillips head screwdriver. After the screw has been removed, you will then need to use a small flathead screwdriver to pry open the back of the fob. Once the back of the fob has been pried open, you will then need to remove the old battery and replace it with a new one. After the new battery has been installed, you will then need to close the back of the fob and screw it back into place.

Let’s dig into it and see what we can uncover.

Step By Step Process On: How To Change Battery Jetta Key Fob?

Here I will explain you step by step process of how to change battery jetta key fob? let’s see how to change battery jetta key fob.

REQUIRED TOOLS:

  1. Thumb
  2. Small Screwdriver
  3. New Battery

Step-01:

To change the battery in your key fob, begin by prying open the key fob with your thumb. You may need to use some force to get the key fob open.

Step-02:

Once the key fob is open, you will see the battery inside. Use a small screwdriver or anything else that will fit to pop the battery out. The battery is spring-loaded, so it may pop out with some force.

Step-03:

To replace the battery, simply slide the new battery into place and make sure that it clips in.

Step-04:

Once the new battery is in place, clip the key fob back together and retract the key.

If you wanted to watch a youtube video that shows you how to change battery jetta key fob? I have included a video below:

How Do I Change The Battery In My Key Fob Vw Jetta?

If you’re like most people, you probably don’t think about your key fob very often – that is, until it stops working. If your key fob has a dead battery, don’t panic. Changing the battery in your key fob is a relatively simple process that only takes a few minutes.

First, locate the small screw that holds the back cover of the key fob in place. Use a small screwdriver or a penknife to remove the screw and the back cover.

Once the back cover is off, you should see a small battery inside. Using a small flathead screwdriver, gently pry the old battery out of the key fob.

Now, take the new battery and insert it into the key fob, making sure that the plus (+) side is facing up. Once the new battery is in place, replace the back cover and screw it in place.

And that’s it! Your key fob should now be working properly. If it’s still not working, you may need to take it to a dealer or locksmith to have it reprogrammed.

How Do You Change The Battery In A 2015 Jetta Key Fob?

If you’re like most people, you probably don’t think about your car key fob very often. But when it comes time to change the battery, it can be a bit of a mystery. Here’s a quick and easy guide to changing the battery in a 2015 Jetta key fob.

1. Start by finding the small release button on the back of the key fob. This is usually located near the bottom.

2. Use a small flathead screwdriver or a paperclip to press and hold the release button.

3. While holding the release button, pull the back cover off of the key fob.

4. Take out the old battery and note which way it was facing. The positive side ( + ) usually has a small bump or raised line.

5. Insert the new battery, making sure it is facing the same way as the old one.

6. Put the back cover back on the key fob and snap it into place.

7. Test the key fob to make sure it is working properly.

That’s it! You’ve successfully changed the battery in your 2015 Jetta key fob.

What Battery Does A Jetta Key Fob Take?

What battery does a Jetta key fob take?

All VW models use a CR2032 battery in their key fobs. This is a small, flat, round battery that is easy to find at any electronics store. Before you begin, locate a small screwdriver and a new CR2032 battery. You don’t want to damage the key fob, so it is a good idea to wrap the flat-head screwdriver with a small piece of tape.

To change the battery, start by unscrewing the small screw on the back of the key fob. This will usually be located near the bottom of the fob. Once the screw is removed, the back plate will come off, revealing the battery. Remove the old battery and insert the new one, making sure that the positive (larger) side is facing up. Replace the back plate and screw, and your key fob should be good as new!

Also, Volkswagen (VW) key fobs use a CR2032 battery. To change the battery:

1. Locate a small screwdriver and a new CR2032 battery.

2. Wrap the flat-head screwdriver with a small piece of tape. This will help prevent damage to the key fob.

3. Insert the screwdriver into the slot on the back of the key fob.

4. Gently pry open the key fob.

5. Remove the old battery and replace it with the new one.

6. Snap the key fob back together.

How Do You Change The Battery In A 2017 Vw Jetta Key Fob?

If you find yourself in need of changing the battery in your 2017 VW Jetta key fob, here are some simple steps to follow. First, locate the small release button on the back of the key fob. Pressing this button will release the back cover of the key fob. With the back cover off, you will see the battery. Using a small flathead screwdriver, gently pry the battery out of the key fob. Once the old battery is out, simply insert the new battery in its place and reassemble the key fob. That’s all there is to it!

Final Word

If your Jetta’s key fob battery is running low, don’t worry – changing it is a quick and easy process. Just follow these simple steps and you’ll have a new battery in no time:

1. Start by removing the key fob from your key ring.

2. Using a small screwdriver or a knife, carefully pry open the key fob case.

3. Take out the old battery and note which way it is facing.

4. Insert the new battery, making sure it is facing the same way as the old one.

5. Close up the key fob case and reattach it to your key ring.

And that’s it! You’ve now successfully changed the battery in your Jetta’s key fob.

Related Post:

Share
Tweet
Pin
Share