How To Change Cmos Battery In Dvr?

As an Amazon Associate, I Earn From Qualifying Purchases.

Last Updated on September 22, 2022 by Ellis Gibson (B.Sc. in Mechanical Engineering)

If you’re like most people, you depend on your DVR to record all of your favorite shows. But what happens when your DVR starts acting up? One possible culprit is a dead CMOS battery. In this article, we’ll show you how to change the CMOS battery in your DVR so you can get back to watching TV.

So, how to change cmos battery in dvr?

There isn’t a whole lot to changing the cmos battery in a dvr. You will need a small screwdriver to remove the old battery and then insert the new one. It is important to note the orientation of the battery when removing it so that you can insert the new one in the same way.

Let’s dig into it and see what we can uncover.

Step By Step Process On: How To Change Cmos Battery In Dvr?

Here I will explain you step by step process of how to change cmos battery in dvr? let’s see how to change cmos battery in dvr.


  1. Screwdriver
  2. New CMOS Battery


First of all, identify the make and model of your DVR. This information can be found on the front or back of the unit.


Once you know the make and model of your DVR, find the CMOS battery. This is usually a small, flat, round battery that is located on the motherboard.


Using a small screwdriver, gently pry the CMOS battery out of its socket.


Take note of the polarity of the battery (which side is positive and which is negative). This information is usually printed on the motherboard next to the battery socket.


Insert the new battery into the socket, making sure to orient it properly according to the polarity markings.


Replace the screw or clip that was holding the old battery in place.


Power on the DVR and check the date and time to make sure that the CMOS battery was properly replaced.

If you wanted to watch a youtube video that shows you how to change cmos battery in dvr? I have included a video below:

What Is The Purpose Of Cmos Battery In Dvr?

The purpose of the CMOS battery in a DVR is to provide power to the BIOS (Basic Input/Output System) when the device is unplugged from a power source. The BIOS is a key component of the DVR that is responsible for its startup sequence and basic operations. Without the CMOS battery, the DVR would be unable to retain these critical settings and would not be able to function properly.

As well as that, The CMOS battery in a laptop is a battery that powers the BIOS firmware. The BIOS is a set of instructions that helps the computer start up. The CMOS battery needs to be working in order for the BIOS to stay operational, even when the computer is not plugged into a power source.

What Are The Steps To Replace A Cmos Battery?

When it comes to replacing the CMOS battery in your computer, there are a few things you need to keep in mind. First, you’ll want to orient the replacement coin cell with the positive side up. Next, gently push the new coin cell down into the battery holder. Finally, replace the node canister cover. With these steps in mind, you should be able to replace your CMOS battery with ease.

An additional, Orient the replacement coin cell with the positive side up. Gently push the new coin cell down into the battery holder. Replace the node canister cover, as described in Removing and replacing the cover of a node canister.

What Is The Easiest Way To Remove Cmos Battery?

The easiest way to remove a CMOS battery is to use a Phillips screwdriver to remove the two screws that hold it in place. Then, gently pry the battery out with a flathead screwdriver.

Does Dvr Have A Battery?

As technology advances, so do the features of our favorite devices. DVRs are no exception – today’s DVRs are more sophisticated than ever, with many offering features like built-in hard drives, Wi-Fi connectivity, and more. But one feature that hasn’t changed much over the years is the need for a battery backup.

Most DVRs on the market today require a battery backup in order to keep recording in the event of a power outage. The battery backup is typically a small, round battery that is located inside the DVR case. The battery backup is used to keep the DVR’s clock running in the event of a power outage, so that the DVR knows when to start and stop recording.

The battery backup is an important part of the DVR, but it’s not the only thing that you need to consider when choosing a DVR. There are many other factors to consider, like the size of the hard drive, the quality of the recording, and the price. But if you’re looking for a DVR with a battery backup, make sure to check the specs before you buy.

As well as that, If your DVR is not working, it might be because the battery needs to be replaced. The battery is a round one that is more than twice the size of a standard watch battery. You can find it inside the DVR case, right up against the BNC connectors.

What Is The Size Of A Dvr Cmos Battery?

The size of a DVR CMOS battery is typically 3.6 volts and about 1200mAh. This battery is used to keep the clock running on the DVR when the power is turned off.

How Do I Change The Cp Plus Dvr Cmos Battery Number?

If you want to change the cp plus dvr cmos battery number, you will need to follow these steps:

1.First, you will need to locate the battery on the cp plus dvr.

2.Then, you will need to remove the old battery from the cp plus dvr.

3.Next, you will need to insert the new battery into the cp plus dvr.

4.Finally, you will need to replace the cover on the cp plus dvr.

What Is The Price Range For A Replacement Cmos Battery For A Dvr?

The price range for a replacement CMOS battery for a DVR can vary depending on the make and model of the DVR. However, you can expect to pay anywhere from $10-$30 for a replacement battery.

What Is The Model Number Of The Hikvision Dvr Cmos Battery?

The Hikvision DVR CMOS Battery is model number DS-2CD2122FWD-IWS.

What Are The Causes Of Cmos Battery Failure?

The CMOS battery is a small, round battery that provides power to a computer’s motherboard. The battery is also known as a RTC (real-time clock) battery. CMOS batteries are found in laptops, desktops, and servers.

The CMOS battery failure can have many causes. One of the most common causes is a faulty or incorrect charger. When the charger is not providing the correct voltage or current, it can cause the CMOS battery to fail.

Another common cause of CMOS battery failure is physical damage. If the battery is dropped or hit, it can cause the battery to fail.

Finally, CMOS batteries can also fail due to age. Over time, the battery will lose its ability to hold a charge and will need to be replaced.

Is It Easy To Replace A Cmos Battery?

No, it is not easy to replace a CMOS battery. The process is delicate and requires special tools. If you are not familiar with working with delicate electronic components, it is best to leave the job to a professional.

Do All Motherboards Have A Cmos Battery?

No, not all motherboards have a CMOS battery. Some cheaper motherboards will not have one, and some higher end motherboards will have a CMOS battery as a backup power source.

What Happens If I Remove The Cmos Battery?

If you remove the CMOS battery, it will reset all your custom settings to the default factory settings. This includes your custom BIOS settings, clock settings, and any custom passwords you have set.

What Is The Purpose Of The Cmos Battery?

The CMOS battery is used to provide power to the CMOS chip, which is responsible for storing system configuration information. Without the CMOS battery, the CMOS chip would lose its data and the system would be unable to boot.

Final Word

If your DVR is acting up, one of the first things you should check is the CMOS battery. This battery is responsible for keeping the clock on your DVR accurate. If it’s not working, then your DVR may have trouble recording or playback footage at the correct time. Fortunately, changing the CMOS battery is a relatively easy process. Just follow the steps below and you’ll have your DVR up and running in no time.


How Do You Reset A Dvr Cmos?

If your DVR is not functioning properly, you may need to reset the CMOS. This can be done by unplugging the power cord from the DVR, removing the battery for 30 seconds, and then plugging the power cord back in.

What Is The Average Price For A Dvr Cmos Battery?

There is no definitive answer to this question as the average price for a DVR CMOS battery can vary greatly depending on a number of factors, such as the brand, the specific model, and where it is purchased. However, a quick search online reveals that prices for DVR CMOS batteries can range anywhere from $10 to $50. Therefore, the average price for a DVR CMOS battery is likely somewhere in the middle of this range, around $30.

What Size Of Cmos Battery Does Hikvision Dvr Use?

The Hikvision DVR uses a CMOS battery that is size AA.

Related Post: