How To Change Rk61 Battery?

As an Amazon Associate, I Earn From Qualifying Purchases.

Last Updated on September 22, 2022 by Ellis Gibson (B.Sc. in Mechanical Engineering)

If you’re anything like me, you’re constantly on your phone and your computer. And if you’re anything like me, you’re also constantly running out of battery. It’s annoying, and it seems like it happens at the most inconvenient times. But it doesn’t have to be this way. In this article, I’m going to show you how to change your rk61 battery so that you can keep your devices charged and avoid those pesky low battery notifications.

So, how to change rk61 battery?

1. Unscrew the back panel of the keyboard using a Phillips head screwdriver.

2. Locate the battery on the back of the PCB.

3. Carefully remove the old battery, making note of its orientation.

4. Install the new battery in the same orientation as the old one.

5. Screw the back panel back on.

Let’s dig into it and see if we can get to the bottom of it.

Step By Step Process On: How To Change Rk61 Battery?

Here I will explain you step by step process of how to change rk61 battery? let’s see how to change rk61 battery.

REQUIRED TOOLS:

1.Keycap Puller 2. Standard Phillips Screwdriver 3. Backplate 4. PCB 5. Battery 6. Soldering Pen 7. Solder 8. Pump 9. Switch Puller

Step-01:

First, you need to use a keycap puller to remove all the keycaps from the keyboard. Make sure to remove all the alphanumeric keycaps first, followed by the mods on the last row. Leave the spacebar for last.

Step-02:

Next, you need to remove the backplate by pulling it up. To do this, flip the keyboard over and gently pull on a switch. Once the backplate is removed, make sure to disconnect the PCB from the battery.

Step-03:

Now comes the fun part – soldering all the switches! Set the soldering pen to 300 degrees Celsius and apply the tip to the solder. Keep the tip on the solder for a few seconds until it is melted, then apply the pump and release.

Step-04:

Remember to clean the pump every once in a while as you are desoldering. This is because solder will get stuck in it, affecting the way it works.

Step-05:

If you find that you can’t remove all the solder, you can try putting more solder on and then reheating it. This will help to transfer the heat to the whole thing and make it easier to desolder.

Step-06:

Finally, use a switch puller to remove all the switches from the keyboard. Once all the switches are removed, the keyboard is ready to be reassembled!

If you wanted to watch a youtube video that shows you how to change rk61 battery? I have included a video below:

How Do I Disconnect My Rk61 Battery?

Assuming you have the RK61 mechanical keyboard, unplugging the old 1450 mAh lithium-ion battery is as easy as gently pinching and pulling from the right and left sides of the connector. Be extra careful when unplugging the old battery as you don’t want to damage the connector or the keyboard.

As well as that, To remove the old battery, unplug it by gently pinching and pulling it from the right and left sides of the connector. Be very careful not to damage the connector when unplugging the old battery.

How Long Does The Rk61 Battery Last?

How long does the RK61 battery last?

The RK61 battery is rated for up to 10 hours of continuous usage. However, if you enable power saving mode, the backlight will turn off after 3 minutes of idle time and the keyboard will enter standby mode after 5 minutes.Deep sleep state will be entered after 10 minutes.

Moreover, The Royal Kludge RK61 is a bluetooth keyboard that can be used for up to 10 hours at a time. It has a power saving mode that will turn off the backlight after 3 minutes of idle time and will enter standby mode after 5 minutes.

What Batteries Does Rk61 Use?

-RK61 uses a rechargeable lithium-ion battery. -The standby time for RK61 is up to 360 hours. -The writing time for RK61 is up to 10 hours. -It takes 3 hours to fully charge RK61.

Additionally, The RK61 mechanical keyboard has a rechargeable battery. It can last for up to 360 hours on standby and 10 hours if you’re using it continuously. It takes 3 hours to charge the keyboard fully.

How Do You Replace Batteries In A Keyboard?

If your keyboard is running low on power, you may need to replace the batteries. To do this, first locate the battery cover on the back of the keyboard. Then, using a small Phillips head screwdriver, remove the screws that hold the cover in place. Once the cover is removed, you will see the batteries. To remove the old batteries, simply disconnect the negative and positive terminals. Then, connect the new batteries in their place and screw the cover back on.

Final Word

If your RK61 keyboard is anything like mine, the battery is easy to change. Just follow these simple steps:

1. Unscrew the back cover of the keyboard.

2. Take out the old battery.

3. Insert the new battery.

4. Screw the back cover back on.

And that’s it! You’ve now successfully changed the battery in your RK61 keyboard.

Related Post:

Share
Tweet
Pin
Share