How To Change Rpm40 Battery?

As an Amazon Associate, I Earn From Qualifying Purchases.

Last Updated on September 22, 2022 by Ellis Gibson (B.Sc. in Mechanical Engineering)

If you’re like me, you’re always looking for ways to save money. That’s why I was interested to read this article on how to change an rpm40 battery. I learned that it’s actually pretty easy to do, and it can save you a lot of money in the long run. I also found out that it’s a good idea to keep a spare battery on hand, just in case.

So, how to change rpm40 battery?

To change the battery in an RPM40, first remove the pod from the device. Next, unscrew the battery cap located on the bottom of the device. Remove the old battery and insert the new one, making sure the positive (+) end is facing up. Finally, screw the battery cap back on.

Let’s dig into it and see if we can find a solution.

Step By Step Process On: How To Change Rpm40 Battery?

Here I will explain you step by step process of how to change rpm40 battery? let’s see how to change rpm40 battery.

REQUIRED TOOLS:

1.Two T5 screws 2. A Stanley blade 3. A heat gun 4. A Phillips screwdriver 5. Contact cleaner 6. A micro USB charger

Step-01:

First, you need to remove the pod from the device. To do this, unscrew the two T5 screws at the bottom of the device.

Step-02:

Then, using a Stanley blade, gently pry off the main faceplate. Be careful not to break the plastic.

Step-03:

Underneath the faceplate, you will see the power button, the wattage adjustment button, and the trigger button. These are all attached to the circuit board with a glue.

Step-04:

Using a heat gun, carefully melt the glue that is holding these buttons in place.

Step-05:

Once the glue is melted, carefully remove the buttons from the circuit board.

Step-06:

Now, the most difficult part: removing the pod unit from the device. This is because the pod unit is glued in place.

To do this, insert a micro USB charger into the charging port and push. The pod unit will slowly start to come out.

Step-07:

Once the pod unit is out, you will see the two wires that are soldered onto the circuit board. These are the positive and negative wires.

Step-08:

Using a Phillips screwdriver, unscrew the four screws that are holding the circuit board in place.

Step-09:

Carefully remove the circuit board from the device.

Step-10:

Now, using contact cleaner, clean the circuit board. Be sure to get rid of any excess liquid.

Step-11:

Once the circuit board is clean, put the four screws back in and screw them tight.

Step-12:

Now, put the circuit board back into the device.

Step-13:

Next, reattach the two wires to the circuit board.

Step-14:

Now, put the trigger button, the wattage adjustment button, and the power button back onto the circuit board. Make sure that they are all properly in place.

Step-15:

Now, using the heat gun, carefully melt the glue that is holding these buttons in place.

Step-16:

Once the glue is melted, carefully put the faceplate back onto the device.

If you wanted to watch a youtube video that shows you how to change rpm40 battery? I have included a video below:

How Long Does A Smok Rpm40 Battery Last?

Are you wondering how long the battery on your SMOK RPM40 will last? Well, the answer may surprise you – it easily lasts for an entire day when used in the 20 – 25-watt power range! That’s right, you can get a full day’s worth of vaping out of this little device, making it the perfect choice for those who are always on the go. So, if you’re looking for a compact and powerful vape that won’t let you down, the SMOK RPM40 is definitely worth checking out.

Additionally, The battery life on the SMOK RPM40 easily lasts for an entire day when using it in the 20 – 25-watt power range.

Why Is My Smok Rpm Not Charging?

If your SMOK RPM 2 isn’t charging, don’t worry – you’re not alone. Many people have had this problem and there are a few things that you can try to fix it.

The first thing that you should do is try charging the device with a different cable. If the RPM 2 still doesn’t charge, try connecting it to a different USB port. You should generally charge the SMOK RPM 2 with a computer’s USB port.

If you’re still having trouble, the next thing to try is a hard reset. To do this, press and hold the power button and the up button for 10 seconds. This will reset the device and hopefully fix the charging issue.

If you’re still having trouble, the next step is to contact SMOK customer support. They may be able to help you troubleshoot the problem or send you a replacement device.

An additional, If you’re having trouble getting your SMOK RPM 2 to charge, the first thing that you should do is try charging the device with a different cable. If the RPM 2 still doesn’t charge, try connecting it to a different USB port. You should generally charge the SMOK RPM 2 with a computer’s USB port.

How Do You Charge A Rpm40?

There are a few different ways that you can charge a RPM40. The first way is to use the supplied USB charging cable. Simply plug the cable into the device and then into a power source. The second way is to use a separate charging dock. These are available for purchase online or at some vape shops. To use a charging dock, simply place the RPM40 on the dock and then plug the dock into a power source. The third way is to use a standard micro USB cable. These are widely available and can be used to charge the RPM40 by plugging them into the device and then into a power source.

Also, To use this mod, first pull the pod out of the device. Then, pull out the rubber plug on the side slot and fill it with e-liquid. After that, replace the plug firmly. To charge this mod, you can use the supplied USB charging cable.

Why Is My Smok Rpm40 Leaking?

It’s common for vapers to overfill their tanks, especially when they’re first starting out. Overfilling your tank is the most likely reason for it to leak. There is a max fill line on your tank. Be sure to never fill your tank beyond the max fill line as it will leak out the top when you use it.

Another common reason for tanks to leak is if the coil isn’t screwed in properly. Be sure to screw the coil in tightly and make sure that the O-rings are in place and properly sealed.

If your tank is still leaking, it’s possible that the airflow holes are blocked. Clean the airflow holes and make sure that they’re not obstructed in any way.

Finally, if your tank is still leaking, it’s possible that the gasket or O-ring on the bottom of the tank is damaged. Inspect the gasket and O-ring and replace them if necessary.

Additionally, Overfilling your tank is the most likely reason for it to leak. There is a max fill line on your tank. Be sure to never fill your tank beyond the max fill line as it will leak out the top when you use it.

Final Word

It’s been a while since we’ve had to change our RPM40 battery. Here’s a quick guide on how to do it.

First, open the battery compartment door and remove the old battery. Next, insert the new battery making sure the positive and negative terminals are facing the correct way. Finally, close the battery compartment door and screw it shut.

That’s it! You’ve now successfully changed your RPM40 battery.

Related Post:

Share
Tweet
Pin
Share