How To Change The Battery In A Ford Key Fob?

As an Amazon Associate, I Earn From Qualifying Purchases.

Last Updated on September 19, 2022 by Ellis Gibson (B.Sc. in Mechanical Engineering)

If you’re like most people, you depend on your car to get you where you need to go. And, if you’re like most people, you also depend on your car’s key fob to unlock your door, start your engine, and keep your car safe. So, what happens when your key fob battery dies? You may be surprised to learn that changing the battery in a Ford key fob is actually quite easy and only takes a few minutes. In this article, we’ll show you how to change the battery in a Ford key fob and get you back on the road in no time.

So, how to change the battery in a ford key fob?

1. Locate the Ford key fob battery cover. This is typically located on the back of the key fob.

2. Remove the battery cover by gently prying it off with a flathead screwdriver or a similar tool.

3. Remove the old battery from the key fob.

4. Insert the new battery into the key fob. Ensure that the battery is properly seated and the + and – symbols align properly.

5. Replace the battery cover and snap it into place.

Let’s dig into it and see what we can learn.

Step By Step Process On: How To Change The Battery In A Ford Key Fob?

Here I will explain you step by step process of how to change the battery in a ford key fob? let’s see how to change the battery in a ford key fob.

REQUIRED TOOLS:

  1. A small flat-head screwdriver
  2. A replacement battery (CR2032 lithium battery)
  3. The remote itself

Step-01:

Firstly, you will need the following things – the remote itself, a small flat-head screwdriver, and the replacement battery (CR2032 lithium battery).

Step-02:

Carefully pry the two halves of the remote apart using the screwdriver. You don’t need to use too much force – just enough to get the job done.

Step-03:

Remove the old battery from the remote and replace it with the new one. Make sure that the positive and negative sides are facing the right way.

Step-04:

Put the two halves of the remote back together and press firmly until they snap into place.

Step-05:

Test the remote to make sure that the new battery is working properly. If it is, you’re all done!

If you wanted to watch a youtube video that shows you how to change the battery in a ford key fob? I have included a video below:

How Do You Change The Battery In A Ford Key Fob?

If you’re like most people, you probably don’t think about your car key fob very often. But when the battery dies, it can be a real pain. Here’s a quick and easy guide to changing the battery in a Ford key fob.

1. Start by finding the right replacement battery. You can usually find these at your local hardware store or online.

2. Once you have the replacement battery, open up the key fob by gently prying it apart with a small screwdriver.

3. Locate the old battery inside the key fob and remove it.

4. Install the new battery in the key fob and reassemble the fob.

5. That’s it! You’ve now successfully changed the battery in your Ford key fob.

How Do You Open The Key Fob On A Ford?

If you’re like most people, you probably don’t know how to open the key fob on your Ford. Here’s a quick and easy guide on how to do it:

1. Locate the small button on the back of the key fob.

2. Press and hold the button for a few seconds.

3. The key fob should now open up, revealing the battery compartment.

4. Replace the batteries and close the key fob.

5. You’re now ready to use your Ford key fob!

How Do You Change The Battery In A 2013 Ford Focus Key Fob?

If you have a 2013 Ford Focus, chances are you have a keyless entry system. This means that instead of a traditional key, your car has a key fob that you use to unlock the doors and start the ignition. The key fob also has a built-in transponder chip that allows you to program it to your car’s alarm system.

While the key fob is a convenient way to access your car, it does have one downside – the battery will eventually die. When this happens, you’ll need to know how to change the battery in your Ford Focus key fob.

Changing the battery in your Ford Focus key fob is a simple process that only takes a few minutes. Here’s what you’ll need to do:

1. Start by removing the key fob from the key ring. You’ll see a small button or tab on the back of the fob – press this in and slide the fob open to access the battery.

2. Remove the old battery from the key fob. You may need a small flathead screwdriver to pry it out.

3. Insert the new battery into the key fob. Make sure the positive ( + ) side is facing up.

4. Close the key fob and test it out. You should now be able to use it to unlock your car doors and start the ignition.

If you have any questions about changing the battery in your Ford Focus key fob, or if you need help troubleshooting any other issues with your car, feel free to contact your local Ford dealership.

What Kind Of Battery Does A Key Fob Take Ford?

A key fob is a small, hand-held electronic device that is used to control various functions of a car, such as locking and unlocking the doors, starting the engine, and opening the trunk. The key fob usually contains a built-in key that is used to activate the car’s ignition. Most key fobs also have a button that can be used to activate the car’s panic alarm.

The key fob uses one coin-type three-volt lithium battery. This type of battery is also known as a CR2032 or DL2032 battery. The CR2032 battery is a small, coin-shaped battery that is about the size of a quarter. The DL2032 battery is slightly larger, but it is the same shape and size as a CR2032 battery. Both types of batteries can be found at most electronics stores.

An additional, A key fob is a small electronic device that you can use to unlock your car doors. It uses one coin-type three-volt lithium battery.

How Much Does It Cost To Replace The Battery In A Ford Key Fob?

The cost to replace the battery in a Ford key fob will vary depending on the model of Ford car you have. However, on average, it will cost between $20 and $30 to replace the battery in a Ford key fob.

How To Change Battery In Ford Key Fob 2015?

If your Ford key fob is from 2015 or earlier, you’ll need to change the battery. Here’s how:

1. Start by removing the key fob from your key ring.

2. Using a small screwdriver or a knife, pry open the key fob casing.

3. Take out the old battery and note which way it was facing.

4. Insert the new battery, making sure it’s facing the same way as the old one.

5. Close up the key fob casing and you’re done!

How To Change Battery In Ford Key Fob 2018?

If your Ford key fob is starting to feel sluggish, it might be time to change the battery. Here’s how to do it:

1. Start by taking off the key fob’s cover. There should be a small notch or tab that you can use to pry it open.

2. Once the cover is off, you should see the battery. It will be clearly marked with a + or – sign.

3. Use a small screwdriver or other tool to gently pry out the old battery.

4. Insert the new battery, making sure that the + or – sign lines up with the corresponding sign on the key fob.

5. Put the cover back on and you’re all set!

How To Change Battery In Ford Key Fob 2016?

If your Ford key fob is not working properly, it may be time to change the battery. Here is a step-by-step guide on how to do so:

1. Start by removing the key fob from your keychain.

2. Locate the small screw on the back of the key fob.

3. Using a small screwdriver, remove the screw and then gently pry open the back of the key fob.

4. Take out the old battery and then insert the new one, making sure that the positive side is facing up.

5. Replace the back cover of the key fob and screw it back in place.

6. Test the key fob to make sure that it is working properly.

What Battery Does A Ford Key Fob Take?

A Ford key fob takes a CR2032 battery. This type of battery is a 3-volt coin cell battery that is commonly used in small electronics.

Can I Replace The Key Fob Battery Myself?

Yes, you can replace the key fob battery yourself. You will need a small Phillips head screwdriver and a new CR2032 battery. First, use the screwdriver to remove the screw on the back of the key fob. Then, pry open the back of the key fob to access the battery. Remove the old battery and insert the new one, making sure the positive side is facing up. Finally, snap the back of the key fob closed and screw it shut.

What Do I Need To Do To Change The Battery In My Ford Key Fob?

If your Ford key fob is not working properly, it may be time to change the battery. Here is what you need to do:

1. Start by removing the key fob from the key ring.

2. Look for a small screw or release button on the back of the key fob.

3. Use a small screwdriver or paperclip to unscrew the screw or release the button.

4. Carefully pry open the back of the key fob.

5. Take out the old battery and replace it with a new one.

6. Close the back of the key fob and screw it or snap it shut.

7. Test the key fob to make sure it is working properly.

What Is The Cost To Replace A Battery In A Ford Key?

The cost to replace a battery in a Ford key can vary depending on the model of the key and the year of the vehicle. However, on average, the cost to replace a battery in a Ford key ranges from $50 to $100.

How Do I Change The Battery In My 2009 Ford Key Fob?

If your 2009 Ford key fob starts to act erratically, or if it stops working altogether, you may need to change the battery. Here’s how to do it:

1. Start by removing the key fob from your key ring. Most Ford key fobs have a small release button on the back that you can press to detach the fob.

2. Once the key fob is detached, use a small screwdriver or a paperclip to pry open the back cover.

3. Inside the key fob, you’ll see a small battery. Use a small flathead screwdriver to carefully disconnect the battery from its terminals.

4. Take the old battery to a local hardware store or electronics store to find a replacement. Make sure to get a battery that is the same size and voltage as the old one.

5. Once you have the new battery, reconnect it to the terminals inside the key fob.

6. Snap the back cover of the key fob closed, and then reattach the key fob to your key ring.

Final Word

If your Ford key fob has a dead battery, don’t panic! Changing the battery is a quick and easy process that anyone can do. All you need is a new CR2032 battery and a small screwdriver. Simply remove the old battery and replace it with the new one, then screw the back cover back on. That’s it! Your key fob will be as good as new.

If you found this article helpful, be sure to check out our other car maintenance tips. And don’t forget to like and share!

FAQ

How To Change Battery In Ford Key Fob 2014?

If your Ford key fob is from 2014 or earlier, the process for changing the battery is pretty straightforward. Here’s what you’ll need to do:

1. Start by removing the key fob from your key ring. Most Ford key fobs have a small release button on the back that will allow you to do this.

2. Once the key fob is free from the key ring, take a look at the back. You should see a small screw that is holding the back cover in place. Use a small screwdriver to remove this screw.

3. With the screw removed, the back cover should come off easily. Be careful not to lose the small spring that may be attached to the back cover.

4. Inside the key fob, you will see the battery. It will be obvious which way the battery needs to go in, so simply replace it with a new one.

5. Once the new battery is in place, replace the back cover and screw.

6. That’s it! Your Ford key fob should now be working properly.

Related Post:

Share
Tweet
Pin
Share